Auto Repair Experience Share

VIDENT iLink400 Software Update Guide

automotiveshop | 10 September, 2019 22:54

OBD360 will give you a step by step instruction on how to update software for VIDENT iLink400 in this post.
Note:
All iLink400 scan tool will be shipped without any Software installed. You can install any software from the following list at your choice by the update client iScanzilla.

alt


 

Software Update
Step One- Install the Update Client
Visit www.videnttech.com to download the update client from
http://www.videnttech.com/support/

alt

 


The file downloaded will be a compressed zip file. Open that file and run the installer inside it.
Alternatively, you can install the update client from the CD that comes in the product package.

Step Two – Create Your Vident Account.

Firstly you need to create an account with Vident.
Once installed, boots up the iScanzilla software, click the Register button.

alt




Fill out the registration form and submit.

alt




Alternatively, you can click the Sign Up button on the right upper side of our website to create an user account.


Step Three – Register Your product

When logged in iScanzilla, click the ‘Register Products’ icon.

alt




On the ‘S/N Registration’ tab, put a tick in the box marked ‘001’ then enter the product’s serial number & password, and click Submit.
Please connect the scan tool with computer through the USB cable, select Setup > About to check the Serial Number and ‘Register Password”.

alt




A confirmation box should be shown confirming successful registration.
Alternatively, you can register the product in the member center when logged in on our website.

alt




Step Four – Download and Install Diagnostic Software
Now close the iScanzilla software, remove the TF card from your tool (making sure the tool is turned off first!) and connect it to the PC via a TF card reader.
Once Windows has detected the TF card, run the iScanzilla software and login again. After a few seconds, a list of the available software updates will appear.

alt




Please select only one software you want to update, as you can ONLY have access to the update of this manufacturer in the future once it’s been selected initially. In case you want to install any other vehicle software, please contact
us or sign in your member center to purchase. Please refer to next chapter to buy extra software.
Click the Update button to download and install the software.

alt


Once the software installed, you can go to Software Management to review the installed software.
Vident iLink400:
http://www.obd360.com/wholesale/vident-ilink400full-system-single-make-scan-tool.html

 

Autel MaxiFlash J2534 Driver Setup & Network Configuration Guide

automotiveshop | 18 August, 2019 23:10

This instruction show you guide on how to install driver and configure network for Autel MaxiFlash J2534.

Autel MaxiFlash Pro J2534 is reliable, fast performance, and flexible; using the OEM software,it is capable of providing dealer-level programming capabilities for all makes,if it work with the AUTEL MaxiSys MS908 and AUTEL MaxiSYS Pro MS908P, Which can do more car

Procedures:
In order for the Pass-Thru Device to operate correctly with the re-flashing and diagnostic applications on the target PC, you will need to first install the MaxiFlash Pro J2534 device driver onto the PC that will control the device.
To setup the J2534 Pass-Thru device driver, you will need the followings:
 CD with the device driver program
 PC or laptop with USB ports
 J2534 Pass-Thru reprogramming tool
 USB cable NOTE: The following steps may vary depending on the operating system or components that are installed on your computer, but in general this is the standard installation process.
1) Insert the driver installation CD to your PC. The driver installation wizard will load momentarily.
2) Click on Next on the welcome page.
3) Select Next on the installation location and installation name. It is recommended not to change the default settings; otherwise the computer may have a hard time recognizing the driver.
4) Click Install and the driver program will be installed onto your PC. NOTE: During this part of the process a MS-DOS style window will pop up and may remain on your screen for a short while, which is perfectly normal. Do not attempt to close the MS-DOS style window manually as this will prevent the device driver being installed successfully, it will close automatically when the device driver installation is complete.
5) Connect the Pass-Thru device to the PC with the supplied USB cable, a Found New Hardware Wizard window will pop up.
6) Select Install the software automatically (Recommended), click on Next, and Windows will search for the driver software automatically.
7) Select the MaxiFlash Pro program and click on Install.
8) When the MaxiFlash Pro device driver program is successfully installed, you should be able to see the Maxi Flash Pro entry in the Device Manager under Maxi Pass Thru Serial.


alt


NOTE: If the driver installation is not complete or unsuccessful, or the PC still can’t recognize the device, an Error or Question mark will display beside the entry icon. Please try installing the driver program again by clicking the entry, then select start auto searching for the software, or manually locate the specific file that contains the driver program.


Ethernet Connection
Using wired network between the Pass-Thru device and the PC, users can choose either way of connection described as below:
Connecting to a PC Directly
1. Connect the PC to the Pass-Thru device with the supplied Ethernet cable.
2. Open My Network Places Properties.
3. In the Properties window, under the LAN or High-Speed Internet heading, right click on the Local Area Connection and select Properties.
4. Now a new window should pop up, titled Local Area Connection Properties. Here you need to select the Internet Protocol (TCP/IP) option, and then click on the Properties button.


http://www.auteleshop.com/wholesale/autel-maxiflash-pro-j2534-device.html

 

Autel MD808 Pro FAQs and Customers Real Reviews

automotiveshop | 01 August, 2019 23:00

Autel MD808 pro scanner is a nice and sturdy device that will allow you to diagnose different car makes and models as long as they are OBD2 compliant and manufactured from 1996 or newer. This includes domestic, European, and Asian vehicles. The diagnostic scanner is easy to use, compact and affordable. It also performs a wide range of functions making it ideal for DIYers, professional mechanics, and technicians.

The MD808 will help you save money as it offers free lifetime updates and upgrades. You can as well save data on the 16GB memory card and in case of any defects on the product; the manufacturer offers a one-year warranty. I hope this Autel MD808 Pro review will help a lot to make a buying decision.

alt

Autel MD808 Pro FAQs:

Q1: Autel MD808 have any advantage over the MD802?
A1: MD808 is much more advanced than MD802.MD808 supports to read and clear trouble codes, control and test BMS /SAS /DPF systems,and reset steering angle sensor (SAS) functionality. These functions MD802 is unavailable to do.Hope it can meet your demands.

Q2: Will this be able yo bring up Transfer Case codes?
A2: Yes,this md808 can read/erase codes on Engine, Transmission, SRS and ABS system as well as lot of special functions.

Q3: Will this unit interface with all of the modules and eletronic controls on a Toyota Prius? And specifically to meter in coolant and bleed brakes?
A3: This md 808 can work on your Toyota Prius on four systems , if wanna get a all system supported product, you can have a look for the MD802 full system or md808 pro.And for metering in coolant and bleed brakes,you may have a look for Autel MK808.

Q4: Autel launched another new product md808. what’s the differences between md808 pro and md808?
A4: MD808 pro is an more advanced professional scan tool than MD808. Though MD808 and MD808 pro are armed the same hardware, MD808 pro has more powerful built-in software system than MD808 pro. MD808 can only access to Engine, Transmission, ABS, and Airbag (SRS) systems while MD808 pro support Read/Clear Codes and Live Data functions for ALL systems.

Q5: Hi this able to bleed abs system on mb gl550?
A5: It will support reading and clearing all codes in all modules. But it would not support the brake bleeding functions. I think you need MX808 to bleed abs system.

Q6: Shops that would use Autel MaxiDiag MD808 Pro?
A6: General repair shops (Perfect for servicewriters), body shops, used car dealerships, auto repair shop, brake facilities, DPF Auto Repair shop, and transmission repair shops

Q7: How do I know if my Autel scanner is genuine or not?
A7: First and foremost, you should buy an Autel scanner from an authorized dealer. If you buy it from an unknown source, you risk being duped or being sold the wrong product. Every Autel scan tool comes with a serial number. After you purchase the device, you need to register it in order to get free software update/upgrade and as well as warranty. As a result, if you try to register the code reader with Autel and it fails, just know that your device is counterfeit. All-in-all, Autel is a reliable company and having a fake product is next to impossible.

Q8: Does the Autel MD808 offer its users with free lifetime updates?
A8: This is where Autel wasn’t clear about its product. In the description, it is written that the product comes with free lifetime updates but it is not. Most users have stated that the free software updates are provided for 3 years and from then onwards, you will have to pay for updates and upgrades. The manufacturer should be clear about this so that buyers are not duped into buying the product.

Q9: I am looking for a scanner that would let me access the onboard computer so that I am able to adjust the vehicle performance which would maximize my fuel economy. Will this model do this procedure or can you suggest a model that can do this
A9: MD808 Pro will tell which fuel injector is faulty and It also able to read fuel trim. If you want full functioning scanner, then you have to increase your budget. You can take a look at the Autel MX808

Q10: This MD808Pro would not link up to a new 2019 Toyota Tacoma. I called US support and was told that I would have to wait at least one year for the update to the device that will cover this and other new vehicles. The support person told me that I would purchase a much more expensive reader with a paid subscription to be able to interact with new vehicles. Thanks Autel for not advising this in your advertising for this product. This MD808Pro will be sitting in my cupboard collecting dust for at least one more years.
A10: Yes, that’s right. If you buy the most recent car model, then low price scanner like Autel md808 pro will not support. They need time( at least one year) to include that new car model with the scanner. All scanner brands follow that type of tactic. Because they need to write a new program for the latest car model to support the scanner

alt

Autel MD808 Pro Reviews:

Review 1:
I did try it out and it did work very well. I work as a gm technician and i use the ms906ts model from autel and they both seem to read the same data. I would recommend any autel product to anyone. They have great products and great technical support. I did the current update on this unit which was simple. The newest update gave you the feature to do the updates through usb. I had to remove the mico sd card to do the updates the first time. You will need a micro sd to sd card adapter if you get a unit with the older software installed.

Review 2:
Autel MD808 Pro was recommended by tire shop because it’s a well made quality product capable of high speed use for sports cars. Product installed and programmed easily for use in my ’06 corvette.

Review 3:
I purchased this to help diagnose an ABS issue and to clear the trouble code(s) when the issue was fixed. It handled these tasks without issue. The ability to see sensors operate in real time and plot them on a graph is invaluable.

Review 4:

This is a new launched product of Autel. My friend bought a MD802 which works very good. This one is an updated version of MD802. It has a bigger screen and memory, and seems the scanning speed is a little bit faster scanning all systems. A very good diagnostic tool.

Review 5:
It clears code fast and works well. It’s an all system diagnostic tool and easy to use. The 16G memory card which enables update is a plus compared to MD802. Though it’s not a bi-directional tool, we won’t get that at this price.

http://www.auteleshop.com/wholesale/autel-maxidiag-md808-pro-all-system.html

How to Use Autel IM608 Reset Battery for BMW

automotiveshop | 21 July, 2019 23:22

Autel IM608 allows displaying the mileage reading of last battery replacement,
registering the battery replacement after replacing a new battery and informing the power management system that a new battery has been fitted to the vehicle.

Autel IM508 System

If the battery change is not registered, the power management system will not function properly, which may not provide the battery with enough charging power to operate the car and limit the functions of individual electrical equipment.

To display the battery history
1. Tap the Service application button from the MaxiIM Job Menu.
2. Tap BMS button and wait for the vehicle manufacturer screen. You can tap VIN Scan or the vehicle make to acquire vehicle VIN information and tap Yes to confirm. See Vehicle Identification on page 34 for detail.
3. Tap Resetting the information to zero on power supply when replacing the battery in the EPB function list, the list may vary for different vehicles being tested.



alt


4. The stored power supply information is reset using this service.Resetting to zero should only be performed when replacing the (main) battery. Once you confirm all the information displayed, tap Continue to proceed.Autel MaxiIM IM608
alt


 5.Tap Start to reset the information to zero.http://www.auteleshop.com
alt


6. Once the reset is completed, the screen displays. Tap Continue.


alt



7. For the Battery Monitoring Sensor (BMS) to calculate the correct battery charging level, the vehicle must be in Sleep mode for a minimum of 4h after reset. In some cases, 6h in Sleep mode may be necessary. Read the onscreen instructions carefully and follow the instructions to ensure vehicle proper functioning.

alt


http://www.auteleshop.com/wholesale/autel-maxiim-im608-advanced-immo-key-programming.html

 

How to Update Autel MaxiCheck Pro Software?

automotiveshop | 27 June, 2019 23:59

ere auteleshop.com share the software update procedures of Autel MaxiCheck Pro,hope it helps!


Procedures:
This function allows you to update the scan tool software through a computer.
Register the Tool
User would update the scan tool ONLY after you had registered the
tool on our website http://pro.autel.com. Then you could download
software, update online, retrieve information and get warranty service.
You can use a Mac or a Windows-based computer to download the
suitable version and proceed.

NOTE: Prior to registration, please confirm your network is working properly.
1. Visit our website http://pro.autel.com.
2. On the Sign In page, input your account ID and other information to log in, if you already have an account.
3. If you are a new member to Autel and do not have an account yet, click the Create Autel ID button on the left side.
4. Enter the required information in the input fields, read through Autel’s Terms and Conditions and tick on Agree, and then click Create Autel ID at the bottom to continue.
5. The online system will automatically send a confirmation email to the registered email address. Validate your account by clicking the link provided through the mail. A product registration screen opens.
6. Select the product model of your tool, enter the product serial number and password on the Product Registration screen, and click Submit to complete the registration procedure.
NOTE: Please use the About function to find out the Product Serial No. and Register Password.

Update Procedure
Autel frequently releases software updates that you can download. The Update feature makes it very easy to determine and get exactly what you need.
1. Install Maxi PC Suite through the included CD, or download the applications in our website: www.autel.com or our distributors’ site. You can use a Mac or a Windows-based computer to download the suitable version and proceed.
2. Make sure that your computer is connected to the Internet.
3. Load the SD card of the scan tool to your PC.
4. Run the Maxi PC Suite. Wait for the Log In window to pop up

alt


5. Enter your Autel ID and password and wait for the Update window to display. If you forget your password unintentionally,you may always click the [Forget Password?] to link to our website and get your password back.
6. Select the product type and serial number, click OK to continue.
7. In the Update window, select the items you want to install.Usually, you should install all available updates.
alt


Generally, there are two ways to update MaxiCheck Pro programs:
Batch Update
Select the programs that you would update by clicking on the check boxes next to those items. Then click the Update Selected Items button on the right side of screen.

Or, click on the Select All checkbox on the right side of screen and all updatable items will be selected automatically. Then click the Update Selected Items button on the right side of screen.

Check the updating process by observing the upper left progress bar [Downloads] and upper right progress bar [Installs]. You may also find progress information in the Status column of updated items.

Anytime you could click the Pause button on the right side of screen to suspend all progresses, and the state of those suspended items would change to stopped.

To resume updating process, you may need to select those suspended items again, and then click the Update Selected Items button. The progress will resume from the break point.

When the downloading is completed, the downloaded programs will be installed automatically. The new version will replace the old version.

Single Update
Find out the desired updating item and click the Install button in the same line. With updating in progress, the Install button changes to Pause.

Check the updating process by observing the upper left progress bar [Downloads] and upper right progress bar [Installs]. You may also find progress information in the Status column of updated items.

Anytime you could click the Pause button in the line to suspend this progress, and the state of this item would change to stopped.

To resume updating process, click the Install button in the line again. The progress will resume from the break point.

When the downloading is completed, the downloaded program will be installed automatically. The new version will replace the old version.

And for more details,please check here:
http://www.auteleshop.com/wholesale/autel-maxicheck-pro.html

 

How to Use CG100 Prog Repair Honda Airbag

automotiveshop | 13 June, 2019 23:22

How to use CG100 PROG III to repair airbag on Honda ECU 77960-T9A-F411-M2 R5F2154 in step-by-step procedure.CGDI BMW Programmer

Model: Honda
No.: 77960-T9A-F411-M2
Chip: R5F2154

1.Power off the vehicle, remove the airbag computer, check the style and the chip.
cg100-prog-iii-repair-airbag-for-honda-01

 cg100-prog-iii-repair-airbag-for-honda-02 cg100-prog-iii-repair-airbag-for-honda-03

2.Open the CG100 special software, choose "Airbag", then "Honda", and wire according to the wiring diagram.
cg100-prog-iii-repair-airbag-for-honda-05 cg100-prog-iii-repair-airbag-for-honda-06 cg100-prog-iii-repair-airbag-for-honda-07

3.After confirming that the wiring is correct, CG100 PROG III is powered on, operate it according to the software prompts in step by step procedure.
cg100-prog-iii-repair-airbag-for-honda-07

Note: Please do not touch any cable when it is reading.
cg100-prog-iii-repair-airbag-for-honda-08

Save file successfully.


Note: Please do not touch any cables when it is repairing.

4.Get message "Repair successfully", please put the airbag computer back on the car and test it if it is ok.


CG100 III tech support is offered by www.obd360.com

XTOOL PS90 Features, Activation, Update and Review

automotiveshop | 27 May, 2019 01:30

Obd360 will show you XTOOL PS90 main features, support language, how to get activation code, how to update and offer you customer review on this product.


What’s the main feature of PS90?
Scans engine, Reads/Clears fault codes, Auto key programming/immobilizer, Oil reset, Turns off service lights, Scans auto transmissions, Turns off SRS airbag lights, Turns off ABS lights, Live data stream.

alt



What’s the PS90 language?
Language: Simplified Chinese, Traditional Chinese, English, Spanish


Where to get activation code?
It is on the user manual. See the following pictures:

alt



How to update?
One-click update via WIFI. Get the latest software whenever you want! Never miss the update with pop-up update reminder.

alt



Customer Review on XTOOL PS90:

The XTool PS90 tool is more than just a code reader. I initially used with a BMW X5 that has had the same emissions related code come and go. After running the automatic diagnostics, the unit reported on information from all the various onboard computers and identified issues that were otherwise unknown. I have had many readers and programmers over the years and this is the only one that had provided the details on the various computer. The unit even identified items that BMW has not reported to the owner. Every vehicle is a little different but so far I have found the information to be beneficial. It should be noted that with some of the features, you want to ensure you have an internet connection. When working remotely, I simply attach the unit to my mobile phone to ensure that the recommendations related to codes are available.

One thing to note is that the bluetooth option allows you to have the tablet away from the vehicle but the OBDII connector still is cabled to the transmit / receive unit but, in most cases, this can be easily placed on the cars dash.

Article from:
http://blog.obd360.com/xtool-ps90-features-activation-update-and-review/ 

How to Use Digimaster 3 to Correct Mileage for 2015 Hyundai Sonata 9

automotiveshop | 06 May, 2019 23:34

Here OBD360 share the guide on how to use Digimaster 3 to program mileage for 2015 Hyundai Sonata 9.

Here I attach 4 images on what I did with Digimaster3:
Digimaster3 correct mileage on 2015 Hyundai Sonata 9-01 

 Digimaster3 correct mileage on 2015 Hyundai Sonata 9-02 Digimaster3 correct mileage on 2015 Hyundai Sonata 9-03 Digimaster3 correct mileage on 2015 Hyundai Sonata 9-04

Solution:
It's confirmed that Digimaster3 is able to correct mileage on 2015 Hyundai Sonata 9, because it can correctly read out the Kilometers.

How to do:
Restore the original data to see if it is normal or not, if it is normal, please correct the mileage again.

Digimaster3 correct mileage on 2015 Hyundai Sonata 9-05 Digimaster3 correct mileage on 2015 Hyundai Sonata 9-06



What did I do after listening to the engineer: 
Because I went into CPU program menu to restore
In CPU program menu you see codes  like FFFFFFFFF 00AA
And it showed me All F
To represent 0

Solution:
Read the KM one more time, then check where is the file saved, then go there to search the data.

Finally, solved perfectly.
It's confirmed Digimaster 3 can correct mileage on 2015 Hyundai Sonata 9 OK

www.obd360.com

Xtool X100 PAD2 Battery Drain and Power off problem

automotiveshop | 09 April, 2019 22:58

Recently,some OBD360 customers feedback  that they have purchased the Xtool x100 pad2 tablet key programmer on our site. But they met a battery problem. For example, One customer left it fully charged and 1 day later, when he tried to use it and it was dead.Also he noticed that the battery drains very quickly while in use, from 100% to 70% in about 15mins. They dont know how to solve this problem, and ask us for help.

After feedback problem to Xtool factory, we have got final Solution from Xtooltech engineer to solve this X100 PAD2 Battery Drain and Power off problem:
Tools required:
1pc* Static bracelet
1pc* Hot air gun  (350±10 Temperature setup: 350±10)

Precautions: Please wear the static bracelet before each operation.

Procedure 1:  Change C6 capacitor
Position: C6
Name: Chip capacitor
Chip specification: 4.7UF/10V  0603
1.Disassemble the C6 capacitor and desolder a 4.7K 0603 resistor

alt

alt

alt

Procedure 2: Remove transistor
Position: Q14
alt

alt



Name: S8050
Chip specification:  0.1uF/50V 0402
1.Disassemble the Q14 transistor.
Procedure 3: Change C123 capacitor
Position: C123
Name: Chip capacitors
Chip specification:  0.1uF/50V 0402
1.Replace the C123 capacitor with a 3.3K%5  0402 resistor.
alt

alt

More products about XTOOL,check here:
http://www.obd360.com/wholesale/original-xtool-diagnostics/ 

 

How to Use Handy Baby 2 to Renew BMW Remote

automotiveshop | 20 March, 2019 23:49

This post show a guide on how to use Handy Baby 2 to renew BMW remote.

What You Need?
JMD Handy Baby II Programmer
Super Chip (S-JMD)
-IOS APP or Android APP with Bluetooth
-BMW Remote
– The Unlock line in the package
jmd-handy-baby-ii-for-bmw-remote-renew-01

Steps:
1.Scan the Handy Baby II APP QR code to download IOS or Android client. (For PC APP, it requires to active).
Install APP.
Register a user name
Bind Handy Baby II machine with the serial number.
***Check register and activation guide
jmd-handy-baby-ii-for-bmw-remote-renew-02 jmd-handy-baby-ii-for-bmw-remote-renew-02 jmd-handy-baby-ii-for-bmw-remote-renew-02
2.Plug the remote line to the S-JMD chip (in red color) , and another end to the Handy Baby II.
jmd-handy-baby-ii-for-bmw-remote-renew-05 jmd-handy-baby-ii-for-bmw-remote-renew-06
3.Pair the Bluetooth in the Handy Baby II and the Bluetooth in the mobile app.
jmd-handy-baby-ii-for-bmw-remote-renew-07 jmd-handy-baby-ii-for-bmw-remote-renew-08
4.Tap “JMD remote”, then “Honda “, then “CRV”, then tap “Create remote”, then choose “Wired”.
jmd-handy-baby-ii-for-bmw-remote-renew-09 jmd-handy-baby-ii-for-bmw-remote-renew-10 jmd-handy-baby-ii-for-bmw-remote-renew-11
5.This is remote and unlock line.
jmd-handy-baby-ii-for-bmw-remote-renew-12
6.This is BMW remote.
jmd-handy-baby-ii-for-bmw-remote-renew-13
7.Connect the cable by following the wiring diagram .
jmd-handy-baby-ii-for-bmw-remote-renew-14
8.Insert to Handy Baby II and BMW remote insert into the coil.
jmd-handy-baby-ii-for-bmw-remote-renew-15
9.Select “Remote”.
jmd-handy-baby-ii-for-bmw-remote-renew-16 jmd-handy-baby-ii-for-bmw-remote-renew-17
10.Take off the BMW remote, select “Remote”, then “Remote renew”, then “BMW” and “5WK49125”.
Please use the unlock line to connect the key.
Press OK to writing.
Write successfully.
jmd-handy-baby-ii-for-bmw-remote-renew-18 jmd-handy-baby-ii-for-bmw-remote-renew-19 jmd-handy-baby-ii-for-bmw-remote-renew-20 jmd-handy-baby-ii-for-bmw-remote-renew-21 jmd-handy-baby-ii-for-bmw-remote-renew-22 jmd-handy-baby-ii-for-bmw-remote-renew-23

Done 

VIDENT iAuto700 All System scan tool Register Guide

automotiveshop | 01 March, 2019 23:24

Step 1: find out the VIDENT iAuto700 serial number and password for registration.
Please connect the VIDENT iAuto700 scanner with a computer with the USB cable provided to boots up it. Select “Setup” on the menu, then “About” and you can see “Product serial number” and password.
Take the user S/N# 7000315001361 for example.
vident-iauto700-registration-01 vident-iauto700-registration-02 vident-iauto700-registration-03
Step 2: login the official site to register.
http://www.videnttech.com/register/step_two.html
As required, to input user ID, password, first name & last name, Country, phone, email and captcha etc.
vident-iauto700-registration-04
Or you can download the “iAuto700 software Update client” to install on your computer to register. Firstly click on “Update client and manuals” and then “iAuto 700“.
vident-iauto700-registration-04

Article from:http://blog.obd360.com/how-to-register-vident-iauto700-all-system-scan-tool/ 

CGDI BMW Programmer BMW Coding and Programming Function

automotiveshop | 18 February, 2019 22:43

CGDI BMW update engineering function incl. G / F /E programming & coding.
CGDI BMW

  1. CGDI BMW can program the following G F E models :
    1)E60(E60\E61\E63\E64
    2) E65(E65\E66\E67\E68)
    3)E7O(E7O\E71\E72)
    4) E89(E81\E82\84\ E87\E88\E90\E91\E92\E93)
    5) R56(R55,R56,R57,R58,R59,R60,R61)
    6) F001(F001,F002,F003,F004,F007,RRO4,RRO5, RRO6
    7) F010(F005,F5006,F010,F011,F012,F013,F018)
    8) F020(F020,F021,F022,FO23,F030,F031,F032,F033
    F034,F035,F036,F080,F082,F083,F087,F088)
    9) F025(F015,F016,F025,F026,F085,F086)
    10) FO56(F039,F045,F046,F047,F048,F049,F052, F054,FO55,F056,F057,F060)
    11) G070(G070,G071)
    12) I001(1001,1012,1015)
    13) KO01(K010,K018,K019,KO21,KO22,K023,K032,K033,K034,KO35,K045,K046,K047,K048,K049
    K050,K051,KO52,K053,KO54,K061,K067,K069,K080,K081,K082,K083,K084)
    14) KEO1(K017)
    15) M013(M013)
    16) KSO1(K002,K0O03,K008,K009,K060
    17) S15A(F090,F097,F098,G001,G002,G011,G012,
    G013,G030,G031,G032,RR11,RR12,RR31)
    18) S15c(G008,G038)

 

  1. Workable modules

Support the modules communicating with K-line and Can bus line , including gateway, airbag, engine, transmission, CAS, dashboard, air conditioning, light module, Footwell Module (FRM) etc.
The unsupported modules: the modules that need Fiber Optic CAN bus and the other bus lines, such as: multimedia display, radio, car information computer etc.

  1. Capabilities

Program the BMW car modules.
Can reprogram the broken module if the module can be communicated.
Automatically read and display the car model and VIN number.

2.CGDI BMW can code for the following BMW G /F /E models:
1) E60(E60\E61\E63\E64
2) E65(E65\E66\E67\E68)
3) E7O(E7O\E71\E72)
4) E89(E81\E82\84\ E87\E88\E90\E91\E92\E93)
5) R56(R55,R56,R57,R58,R59,R60,R61)
6) F001(F001,F002,F003,F004,F007,RRO4,RRO5, RRO6
7) F010(F005,F5006,F010,F011,F012,F013,F018)
8) F020(F020,F021,F022,FO23,F030,F031,F032,F033
F034,F035,F036,F080,F082,F083,F087,F088)
9) F025(F015,F016,F025,F026,F085,F086)
10) FO56(F039,F045,F046,F047,F048,F049,F052, F054,
FO55,F056,F057,F060)
11) G070(G070,G071)
12) I001(1001,1012,1015)
13) KO01(K010,K018,K019,KO21,KO22,K023,K032,
K033,K034,KO35,K045,K046,K047,K048,K049
K050,K051,KO52,K053,KO54,K061,K067,K069
K080,K081,K082,K083,K084)
14) KEO1(K017)
15) M013(M013)
16) KSO1(K002,K0O03,K008,K009,K060
17) S15A(F090,F097,F098,G001,G002,G011,G012,
G013,G030,G031,G032,RR11,RR12,RR31)
18) S15c(G008,G038)

  1. Testable modules

Support the modules communicating with K-line and Can bus line , including gateway, airbag, engine, transmission, CAS, dashboard, air conditioning, light module, Footwell Module (FRM) etc. The specific module will be known according to the car’s configuration information.

  1. Capabilities

1) Backup & coding, restore coding, coding etc.
2) To set code for the module after the car module is programmed or replaced.
3) Automatic read and display the car model and VIN number.

www.obd360.com

Article from:http://blog.obd360.com/cgdi-bmw-update-g-f-e-programming-coding-works/

 

How to Use Yanhua Mini ACDP Read/Write Jaguar/Land Rover?

automotiveshop | 22 January, 2019 22:31

In this article i want to show you how to use Yanhua Mini ACDP to read and write EEPROM for Jaguar & Land Rover?And for more about Yanhua Mini ACDP you can search here:http://www.obd360.com

Procedure:
In the left rear of the car, open the plaque, see the fuse box, remove the fuse box and see the RAF smart computer
raf-smart-computer-01

Connect Yanhua ACDP to OBP+ ICP adapter, then to BDM adapter, then to KVM adapter. Wait the indicator turn red then green.
yanhua-mini-acdp-connects-land-rover-kvm-module-02 yanhua-mini-acdp-connects-land-rover-kvm-module-02

Click on “LandRover” option.
yanhua-acdp-program-landrover-kvm-mc9s12xeq384-3m25j-04

Click on ” KVM (MC9S12XEQ384 112Pin)”.
yanhua-acdp-program-landrover-kvm-mc9s12xeq384-3m25j-04

Click on “IMMO”.
yanhua-acdp-program-landrover-kvm-mc9s12xeq384-3m25j-04

Come to the main menu:
MC9S12XEQ384_0M12S
MC9S12XEQ384_1M12S
MC9S12XEQ384_2M25J
MC9S12XEQ384_3M25J
yanhua-acdp-program-landrover-kvm-mc9s12xeq384-3m25j-07

Choose ” MC9S12XEQ384_3M25J”
yanhua-acdp-program-landrover-kvm-mc9s12xeq384-3m25j-08

Click on ” Add key auto mode”
Starting application.
Device connection succeed.
Note: Please prepare the OBP+ICP adapter, BDM adapter, KVM module, BAV adapter and Blank key.
yanhua-acdp-program-landrover-kvm-mc9s12xeq384-3m25j-09

Follow the tip to ensure the well connected for ACDP device, OBP +ICP adapter, BDM adapter and KVM module.
yanhua-acdp-program-landrover-kvm-mc9s12xeq384-3m25j-10

Detecting pins status, please wait..
Good contact and continue.
yanhua-acdp-program-landrover-kvm-mc9s12xeq384-3m25j-11 yanhua-acdp-program-landrover-kvm-mc9s12xeq384-3m25j-12

Configuring adapter, please wait…

It is detected the KVM module chip has been encrypted, whether to continue? click on “Continue”.
yanhua-acdp-program-landrover-kvm-mc9s12xeq384-3m25j-12

Configuring adapter, please wait…
Decrypting the chip, please wait… It will take several minutes.

Reading chip PFLASH data, please wait…

Please save the original PFLASH data of the KVM module.
yanhua-acdp-program-landrover-kvm-mc9s12xeq384-3m25j-14

Uploading data…
yanhua-acdp-program-landrover-kvm-mc9s12xeq384-3m25j-15

File save path.
yanhua-acdp-program-landrover-kvm-mc9s12xeq384-3m25j-16

Reading chip EEPROM /PFLASH data, please wait…
yanhua-acdp-program-landrover-kvm-mc9s12xeq384-3m25j-17

Please save the original EEPROM data of the KVM module.
yanhua-acdp-program-landrover-kvm-mc9s12xeq384-3m25j-18 yanhua-acdp-program-landrover-kvm-mc9s12xeq384-3m25j-19

Just click “Yes” until you see the immo info shown as below.
yanhua-acdp-program-landrover-kvm-mc9s12xeq384-3m25j-19

Just follow the on-screen instruction to do .

Please choose to add the keyway.
Choose key 6.
yanhua-acdp-program-landrover-kvm-mc9s12xeq384-3m25j-21

Just follow the on-screen instruction to operate.
One more time, it will show “Decrypting the chip, please wait… ” and it will take several minutes again.
Next is writing chip EEPROM /Plash data, please wait…
Checking chip data, please wait.

Adding the key complete. Please install the KVM module to the car and confirm that the new key can be used normally.
yanhua-acdp-program-landrover-kvm-mc9s12xeq384-3m25j-22

Done.

PS: just use the same way to program new key when all keys lost. 


Article from:http://blog.obd360.com/how-does-acdp-read-write-jaguar-land-rover-kvm-data-via-icp/ 

How to update SEC-E9 key cutting machine ?for Tablet PC Bluetooh Version?

automotiveshop | 14 January, 2019 03:13

This post show a guide on how to udpate SEC-E9  for table PC bluetooth version.

Procedures:

  1. Click “Setup”

alt

  1. Click”Wifi”

alt

  1. Connect Wifi
  2. Press “UpdateCheck” after the wifi is connected successfully.

( Please notice that you just need to click the “UpdateCheck” once, no need to click it repeatedly)
alt

  1. Click “Upgrade” button

alt

  1. After upgrading successfully, the tablet PC will automatically jump to the main page.

alt
Tips:

  1. Please keep the Wifi linkedwhen upgrade
  2. Please keep the network smooth
  3. Please do not close tablet PCwhen upgrading
  4. Please do not operate the tablet PCwhen downloading the upgrade files.
  5. Please disconnect Wifiafter upgrade is done. ( otherwise the system will generate garbage when tablet PC updates automatically. Also  cause the system to run slowly.)

Source:http://www.obd360.com/wholesale/sec-e9-cnc-automated-key-cutting-machine.html 

 

Lonsdor K518 Customers Feedbacks Work and Not Work!

automotiveshop | 03 December, 2018 04:42

After more than one year of test and conclusion, a sheet of Lonsdor K518ISE Key programmer feedabck was formed, it is newest and most comprehensive.

More info about is please visit:http://www.obd360.com

alt

1. Lonsdor K518ISE: New 3 month trial period for certain special function.
I used it for Megane 3 with Smart Card system. Programmed key card in 2 minutes. No need pin code or anything….
Seems they have finally got a good competition for the Zedfull…..
2. Good news !! New update is good for MQB key !! Work fine add key on golf mk7 2015 ! Very fast and easy !!! Bravo !!
3. Mégane 3 RS 2010, 4 buttons card, hands free. Cards programmed 2 mins, Starts/stops, opens/closes, and the hands free works too with factory cards.
4. Renault espace 2008 added 2 smart cards with no error, after finished the 2 cards were not recognised did not start car or work central locking
took long while, 5 minutes per card, MVP coded all cards in under 30 seconds, working perfect…
5. I made cas 2 one week ago no problem at all i made key in slot off lonsdor max 5 min
6. Personaly I never had issue with BMW cas 2/3 with lonsdor
7. Volvo v50 2005 add key and remote ok
8. Fiat doblo 2017. Program key ok And desabled key lost.
9. Honda accord 2012. Add key ok.
10. Renault master3 2012 add key ok
11. BMW 1 F25 2012 fem add Key ok
12. Read pin add key Peugeot 208 2014 ok
13. Mazda cx9 2015 add key 4d-63 80bit ok
More…… Lonsdor K518ISE test reports yes & no.

Article from:Lonsdor K518ISE Key programmer Feedback Yes & No (Newest & Complete) 

 

1 2  Next»
 
Provided by Multiblog.net - easy blogging platform
P0wered by L1fe7ype - De51gn by Ba1earWe6